Ford axle identification.
1932-1934 the wishbones are bolted to the bottom of the axle housings about 8" from the ends. the tabs for the wishbones are welded on, but will not go all the way around the housing, just the bottom. the spring hangers are forged on to the axle tubes. on the 1932, the part where the torque tube bolts to the diff is round (most) it is more of a ...
For independent front suspension (IFS) axles, the B/M number may be located at one of three locations: 1). A vertically positioned tag near the center of the right hand side support arm, 2) stamped into the left hand side support arm (opposite end of the camber adjuster), or 3) stamped into the “nose end” of the axle carrier. The location ...Ford Truck Enthusiasts Forums. Older, Classic & Antique Trucks. 1987 - 1996 F150 & Larger F-Series Trucks. 1 TON Axle Identification. Notices. 1987 - 1996 F150 & Larger F-Series Trucks 1987 - 1996 Ford F-150, F-250, F-350 and larger pickups - including the 1997 heavy-duty F250/F350+ trucks. Sponsored by:This page should help. Following the 17-digit VIN on your truck, select the character for each box that matches it’s place in the VIN. Sample V.I.N. (Vehicle Identification Number) Typical VIN. Position Number.Ford Rear Axle Assembly Identification - Page 17: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: V106A: Ford F250 Pickup 85-86: 3.55: 10.25: NL--V106B: Ford F250 Pickup 85-86: 3.55: 10.25: NL--V106C: Ford F250 Pickup ...Clutch, Transmission, Differential, Axle & Transfer Case - Rear Axle Identification... - I have an 87 Ford F-250 with a 6.9 Diesel and am trying to figure out what axle it has in the rear. I am looking for a dana 60 to put in my mud truck and this axle looks about like a dana 60 although it is not a full-floating...
Oct 30, 2015 ... Mr. Regular leans how to identify a Ford 7.5 vs a 8.8 by the differential cover. The Vagabond Falcon needs a Ford 8.8 rear that is 56 inched ...
Sep 28, 2004 ... The Ford "8 3/4" is just a 9" with a slightly smaller ring gear. Otherwise identical, and regular 9" parts can be used for a rebuild. Here is a...streetrodderbn. The 9in ford came from the factory with 2 seals per axle, one is a rubber seal that is in the axle tube itself and the lip seal rides on the axle, the 2nd seal is a thin metal one that sandwiches between the axle bearing retainer and the housing axle flange to seal the outside of the bearing.
Jan 14, 2021 ... this video delves part way into the rear axles and ratings for the F-150 HD 9.75" and light duty Super 8.8" rear axles while showing part ...Sep 3, 2002 · Quick response please. I'm looking at a truck to buy with the Vin of 2FTJW35G3JCA52842. Can the rear axle ratio be deciphered from this info? I'm interested in a towing truck and I think the axle is a 3.55 (35 in the vin #). I already have a truck with a 5 speed and 3.55. It's on ebay, so a quick response is appreciated. Tony. This makes them a popular axle for vehicles on the street and at the track. It is important to understand the design, components, identification, and functions before building or rebuilding a Ford 9" rear axle. Below are answers to the most common questions about the Ford 9” differential: How To Identify A Ford 9 Inch Rear EndDifferent rear springs. 1973 - 1979 F-100 & Larger F-Series Trucks - 1 ton Dually GVW and Axle Identification - Morning all, I recently acquired this old '78 ford dually to fill the roll of water truck on my small farm. There was no title but it was clear it had been a farm truck its whole life. The old grain box on the back had been torched...No idea, the above diagram I posted came straight out of the Ford shop manual that dealer tech's use. 2009 - 2014 Ford F150 - Help Me ID This Rear Axle (Code S930P) - I'm looking to buy a rear axle assembly to mock up some things for a project I'm starting and I'm wondering if anyone can help me identify which rear axle is in this picture, the ...
The simplest way to identify the rear axle assembly of a Ford vehicle is to look at the plate stamped on the component. The plate provides important information about the axle asse...
Decoding Ford axle tag codes is crucial for identifying the specific axle installed in a vehicle, making accurate repairs and upgrades, and conducting vehicle …
The dealer installed lighting kits were changed to include sealed beam Ford headlights, replacing the larger C.M. Hall headlights which had been in use since '39. At serial 167488 the front axle/radiator support was again updated to a stamped steel design that would be used on into the 8N production.Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear End Tag No. - Identification Help. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by:Ford Rear Axle Assembly Identification - Page 05: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDY-A, A1: Comet '66-69 Fairlane '66-70 Falcon '66-70 Montego '70-74 Torino, '71-'74: 3.00: 8 in: NL: 28-1987 - 1996 F150 & Larger F-Series Trucks 1987 - 1996 Ford F-150, F-250, F-350 and larger pickups - including the 1997 heavy-duty F250/F350+ trucks. Sponsored by: ... Ford Rear Axle Assembly Identification - Page 11 - FORDification.com 4.10 = ratio. If it had an 'L' between 4 & 10 it would be limited slip. 10 2 = ring gear diameter. 10.25" ...For 2015 models, the maximum towing capacity of a Ford F-350 ranges from 12,100 pounds to 26,500 pounds, depending on the configuration of the vehicle and the trailer. Vehicle opti...Dana models with similar gasket shapes include Dana 25, 27, 30, 60, 70, and 80 but you need access to the identification tag to confirm this. There are two identification tags in every Dana. The first one is located on the driver's side differential carrier and the second tag is usually cited on the passenger side of the axle cover.Generally most cars received 28 spline axle shafts. These were the Hi performance 302s, 427s, 428's and the 429 cars which received the 31 spline axles. Later on, some of the trucks received the 31 spline axles as did some Lincolns and Thunderbirds. If you see a " N " case center section chances are very good it has 31 spline axles. …
2005-2016 Ford Dana Super 60 Front Axle ID. Ford used Dana Super 60 Front Driving Axles in 2005-2016 F250, F350, F450, and F550 Super Duty 4x4 trucks. Each axle is built with a Bill of Material (BOM) Tag affixed to the differential cover by two cover bolts. These axles will also have a white data decal on the right axle beam that shows the BOM ...One of the most common questions we are asked is how to tell if your Bronco has a Dana 30 or a Dana 44 Front End. Once you know what to look for, it is very simple to decipher between the two. The quickest way to tell is to look at the top of the steering knuckles where the Front End Housing is connected to the Knuckle.Ford Rear Axle Assembly Identification - Page 12. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.B4J: B4 = Rear Axle Code = Dana 60 / 4.10-1 / Limited Slip / J = Front Axle Code for Power Steering. The ID tag which is under one of the bolts that holds the inspection cover on, is only used on Dana 44's, AFAIK. Most of the time, it's missing. On the 60's and 70's the ID tag is on that thin metal ID tag which is bolted onto the left axle tube ...The third character is for the vehicle model code. For example, R3 is Mustang, H7 is F-Series Short Cab, L3 is F150/250. So a 2011 Mustang axle is part number BR3W-4001-KH. The last character designates which Design Engineering Office is responsible for the component. There is a fair amount of detailed information contained within the part ...Jan 27, 2023 · The Ford 8.8 Rear Axle Is Cheaper Than a 9-Inch. 10) Most 8.8 axletubes are 3 inches in diameter and very thin. To prevent warping from heat, don't use a torch and avoid extended use of a die ...
Axle Identification. I have a 1979 Ford F-150 Ranger Lariat 4WD. I am trying to figure out what axles are under it. I'm sure the rear end is a 9 inch with 3.50 gears. Here's the info. The tag in the door reads 16A for the axle. The front axle's tag reads 3.50 D9TA AAA and 610047-4. The rear axle was more difficult with a small tag reading 8G25 ...
E-350 Dana axle M70FF (M267FF). 3.28 qt (3.1 L) 1. E-450 Dana axle M70HD (M273HD). 4.86 qt (4.6 L) 1.Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. F350 Axle identification. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by:Ford Rear Axle Assembly Identification - Page 01: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WBG-E : Ford Truck '63-71 F100: 3.70: 9 in: NL: 28-WBG-F : Ford Truck '63-71 F100: 3.89: 9 in: NL: 28-WBG-H: Ford Truck ...Table of axle codes for the Ford F-150. In the table below you can see a selection of two-character codes, simply read across to the left to find your axle ratio – 3.31, 3,55 3.73, 4.10 and 9.61 for the lightning. You can see that codes that are purely numeric (e.g. “19“) correspond to a Non-limited slip, and codes with a letter (e.g. “L6“) correspond …Looking to identify my front axle, these are pictures of the tag. Tag is very dirty making it hard to read. Ford: D7TA-ANA / Dana: 603808-9 = Dana 44.7F Front Driving Axle / 3.50-1 / Free Running Hubs / No Limited Slip / 3,500 lbs. Capacity. Tag is very dirty making it hard to read.Personally, I would suggest the 1957/72 F100 9" as it fits. I don't know if the others will and all the others have specific R & L axle shafts, while the F100's are the same R & L. F100: 1957/67 have 11" x 1 3/4" rear brakes, 1968/72 have 11 x 2 1/4" rear brakes. diff/axle identification.Early Ford Axle Identification. This article will cover Ford axles from 1928-52 passenger cars & pickups. Keep in mind, this is for Ford cars & pickups only. Trucks and other makes such as Lincoln do not apply. Ford Model A Axle Spring Perch Boss = 2.25" Perch Boss Center to Center = 36.5" Kingpin Center - Center = 50.5" Kingpin Diameter = 0.8125"
Dana models with similar gasket shapes include Dana 25, 27, 30, 60, 70, and 80 but you need access to the identification tag to confirm this. There are two identification tags in every Dana. The first one is located on the driver's side differential carrier and the second tag is usually cited on the passenger side of the axle cover.
from elizabethtown kentucky. darnit. i guess there is a difference in spindle size. mine is so big the bearings wont fit. so now im looking for 47-53 1/2 ton spindles or a new axle. either or. shtterbug8, Mar 10, 2013. SHARE POST #8.
Component 1: Axle Ratio. The axle ratio is the numerical representation of the gear ratio, which expresses the number of revolutions the driveshaft makes for each revolution of the axle. It determines the vehicle's torque, towing capacity, and fuel efficiency. Common axle ratios found in Ford vehicles include 3.31, 3.55, 3.73, and 4.10.The Ford 3E axle code can have a significant impact on the performance and capabilities of a Ford vehicle. The 3E code represents specific gear ratios and differential types, which can influence factors such as towing capacity, acceleration, and fuel efficiency. By understanding the 3E axle code, drivers can make more informed decisions about ...Ford for 2006 MY applied the "wide trac" front axle (Dana Super 60) to the Super Duty Pickup trucks. It was applied under the "TOW BOSS" package ONLY for the 6.0L F350 DRW trucks with an automatic transmission. Yes, you might get 3.73, 4.10 or 4.30 gears using the 6.0L, 5.4L, or 6.8L motors and other transmissions.The 1985 to 1991 Ford F350 Dana 60 axles have a unique to Ford, reverse spiral ring and pinion set available in either 3.54 or 4.10 gear ratios. Axle Type: Mono Beam 1-piece iron housing, 4x4 front steer with full-floating axle shafts, and dual piston caliper disc brakes Cover: 10 Bolt, 12" high Ring Gear: 9-7/8", 12 Bolt. Suspension: Leaf spring2017+ Super Duty - 2023 F350 axle ID - My sterling in my 2019 F250 had 12 bolts on the differential cover. The one on my 2023 has 16 bolts and massive tubes. ... Ford built axles have a fill plug tapped into the iron case, usually to the left side of the pinion snout. The case is drained by removing the lowermost cover bolt.These images of Christine Blasey Ford's appearance before the Senate judiciary committee illustrate the the extraordinary nature of the proceedings. Images of Christine Blasey Ford...Look at the tag on your driver door. There is a category for Axle Code. Look at that code then Google it. You likely have 3.55 if you have a 4x4 or FX4 or max towing. Otherwise 3.31 would get my vote. The 10 speed trans defaults to the 3.31 unless other criteria is met as the 3.31 is a perfect match for the 10 speed.You are here: Home Tech Articles Front / Rear Differentials Ford Rear Axle Identification - Page 02. ‹ Back to Technical Index. Ford Rear Axle Assembly Identification - Page 02. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L. Axle Shaft Splines.
Ford Rear Axle Assembly Identification - Page 11: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: S157B: Ford F250SD, F350SD Pickup ‘99: 4.10: 10.50: L--S157C: Excursion '00 Ford F250SD, F350SD Pickup ‘99-01: …1965 Ford Mustang Axle Information & Ratios. The first table is the code and gear ratio. If you know your axle tag number, simply go to the second table. Axle code: Ratio & type: 6: 2.80 open differential: F: 2.80 locking differential: …The AXLE code usually contains 3 digits, the first 2 are for the rear axle, but these digits are missing because the truck was a Domestic Special Order. Rear axle was installed after the truck left the assembly line. N = Ford 9,000 lbs. Capacity Front Axle with Power Steering. 27,500 lbs. Gross Vehicle Weight Rating. 730104:Instagram:https://instagram. chevy equinox lug nut torquecobleskill price chopper pharmacybigtreetech skr mini e3 v3 klipperhome depot 24 month financing promotion code 2023 credit card Look at the tag on your driver door. There is a category for Axle Code. Look at that code then Google it. You likely have 3.55 if you have a 4x4 or FX4 or max towing. Otherwise 3.31 would get my vote. The 10 speed trans defaults to the 3.31 unless other criteria is met as the 3.31 is a perfect match for the 10 speed. cybermonk zenyattaraquel welch bust size House centipedes can be an unsettling nuisance, but you can get rid of an infestation. Here’s how you can identify and remove a house centipede problem. Expert Advice On Improving ... jack begley age The third character is for the vehicle model code. For example, R3 is Mustang, H7 is F-Series Short Cab, L3 is F150/250. So a 2011 Mustang axle is part number BR3W-4001-KH. The last character designates which Design Engineering Office is responsible for the component. There is a fair amount of detailed information contained within the part ... Your medical ID number is a unique set of numbers that the health insurer will give you when you enroll in one of its plans. It is useful for identifying who you are and the extent...Dec 13, 2023 · Decoding Ford rear axle codes can be a bit complex, but by following a step-by-step process, it becomes much easier. Each letter and number in the rear axle code has a specific meaning, allowing you to extract valuable information about your axle. For example, the first two letters of the code indicate the axle’s size and capacity, while the ...