Lml duramax crank no start.

Finally got the truck to fire and run. it takes 20-30 pumps to get the primer firm. it has no visible leaks around it and all the lines from it. when the motor is cool it …so I measured the FRP and got 585 while cranking, and 4900-5100 psi at idle. For one of my multiple start pressure tests I threw a code but havent had the code come back on. it was P0341 Camshaft position sensor, after I moved past the code screen to check my rail pressure I was getting 941 psi while trying to start it that one time, now it went back to 585 psi with no code again.2013 lml won't start. To keep it short n sweet I'm new to the diesel world..bought a brand new 2013 sierra 2500hd 6.6 lml..drove truck for 1,000 miles around town with no issuses..drove the truck 4,000 miles this past week to Vegas for sema pullin enclosed trailer and pulled its ass off n couldn't b happier with the performance..Sunday night ...I have a 2016 LML that will crank, not start. It's been at a diesel repair shop 4 weeks and they can't figure it out. I was getting new tires put on and asked the place if they replaced fuel filters also. They replaced the fuel filter, I drove it 3 miles, next morning it would crank but not start. Had it towed back to them, they put a different ...Oct 7, 2018 · Connect a test lamp between the control circuit terminal 86 and the ground circuit terminal 85. Turn the ignition to the start position. The test lamp should turn ON when the ignition is in the START position, and OFF in all other positions. ¤ If the test lamp is always on, test the control circuit for short to voltage.

Knocking continued with foot applied on brake pedal and in drive/reverse 1200-1600 rpm “knock” “knock”, cylinder cut out test found sound coming from #6 cylinder. Replaced #6 fuel injector. Same issue “knocking” under low RPM. Two days later, Removed engine and disassembled completely to find no issues to Pistons, crank, rods, Heads ...This switch is located in the suction side of the fuel system and it may induce a crank no start, hard start, or an extended crank. Note: The Chevrolet Express and GMC Savana vans utilize a Fuel Conditioning Module with an electric priming pump. The filter minder switch will have to be inspected with the electric prime pump running. See more. 1.

2012 LML Duramax LTZ Crewcab. CSM canopy. Full delete. 6" Procomp lift plus air bags Mickey Thompson 305/70/R18; twin spares. ... Confirm actual versus desired rail pressure even under crank no start conditions, to confirm the starting issue is rail pressure related. If rail pressure matches desired, diagnose other codes that may be related to ...

LML runs a few seconds then dies. Preparing for the full delete and tunes, I installed a Fass 150 last week. Truck started and ran fine since. Yesterday I installed the S&B and a fuel filter delete. Also drilled manifold and installed egt probe. After heavy cranking the truck will start and run a few seconds then die.143 posts · Joined 2022. #4 · Mar 9, 2022. I had the tcm go out on my lml. Flashing service stabilitrack and traction control on the display. Was followed with a P0700 code. Loss of power, stuck in gear, hard shifts especially going Into reverse. I believe a bad tcm can also cause a no crank aswell but not 100% sure on this.I have done a couple of these conversions with little to no trouble and some not even having to be retuned to run well. I have been putting in stock lbz pumps. This is a 2016 cab and chassis that had the classic cp4 failure. I installed lbz pump and new lml injectors and started and ran like a top, but anything above +- 10percent throttle it ...Jun 18, 2023. #1. 2016 LML duramax, cp3 swapped (before rebuild all tuning is for cp3 swap), fass 165, installed Mahle performance pistons and rings, I've bled all the air you can possibly think. Maybe there's more left. I'm between 430-450psi in all cylinders as well, did a manual compression test after completing the rebuild.For the past week and a half, I've had my 2011 LML on my lift while I installed a CST 4" suspension lift. I drove the truck into the shop to put on the lift and it was running great. I didn't touch any electrical connections and wires (aside from disconnecting and then reconnecting the ABS wires to the hubs) during the entire install. I ...

441 posts · Joined 2010. #14 · Nov 27, 2012. the wait to start light was not used on duramax engines. there is a light that looks like a curly line to represent a glow plug, but they do not have the wait to start like the old gm diesel engines did. the boss had the LB7, LLY, and LBZ engines and none of them had a wait to start light, just the ...

Possible someone shimmed the valve and lost parts-- COMMON. Pull the "U" hose from the fuel rail-- plug the hose. Connect a hose to the nipple on the fuel rail. Crank the engine--- any fuel coming out of the fuel rail nipple -- the FPRV is leaking fuel-- IT WILL NEVER START.

Subject: Duramax Diesel Crank No Start, Hard Start, or Extended Crank Models: 2010-2011 Chevrolet Express, Silverado 2010-2011 GMC Savana, Sierra Equipped with the 6.6L Duramax Diesel Engine RPO codes LGH and LML The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI. Condition/Concern: A dealer may ...The 2011-2016 6.6-liter LML Duramax V-8 engine is the capstone of GM's Pre-L5P turbodiesels. Here are some vital facts about the iconic truck engine. ... The LML not only meets the stringent ...Crank no start2011 lml duramax. fuel rail pressure at crank no start2011 lml duramax. fuel rail pressure at startup will barly reach 1500 psi but when started it runs just under 5000psi at idle and up to 26000 running down the road.Close the vent and pump it till the plunger won't move any longer. Once it is hard, try and start the truck. If it does not start, pump it til it is hard again and repeat as necessary. If you never stop getting aerated fuel, you have an air leak between the tank and the filter head. 2009 Silverado 2500HD CCSB LTZ Diesel.JChrist705 Discussion starter. 67 posts · Joined 2008. #6 · Oct 10, 2012. It's got about 57% life left according to the DIC...right now that's the prime suspect. Sent from my Autoguide iPhone app. 2008 LMM Silverado 2500HD LTZ. -Cognito UCA kit and braces. -NorCal Nick "Large" fender mod. -20x9 Ultra Maverick wheels, 5"BS / 0mm offset.Duramaxtech21. 4 posts · Joined 2015. #6 · Jan 30, 2015. You won't have metal in the filter. And yes the fuel is high pressure from the pump to the injectors at 31000 psi so only way to actually determine if you have pressure is to pull a few glow plugs easy to access once you take the inner finder out on the passenger side then you would ...2011 duramax lml no crank no start. Jump to Latest Follow 302 views 2 replies 3 participants last post by Ron Nielson Nov 6, 2023. R. Romanov Discussion starter 3 posts · Joined 2023 Add to quote; Only show this user #1 · Nov 5, 2023. Bought truck about 2 months ago, it was blown, needed new rods and bearings. crank as well. ...

before Monday (but only for a week before) I had noticed every now and then cold or hot engine it took an extra second or two of cranking to get the truck to start. towed it to my trusted dealer (But not without my brother bragging about it) Injector pump out at 94k miles. some screen on the regulator was full of metal, which requires all lines ...1 post · Joined 2020. #1 · Feb 23, 2020. I have a 2012 Chevrolet Silverado LML 6.6 3500hd. Recently had to do a motor swap due to a broken crank shaft. I Swapped the motor now I'm having a No Crank / No start Issue. Thought maybe bad wiring harness so I swapped harnesses, Wasn't the issue, Doing that same thing. The starter does work!3.0L Duramax Reliability. The crank no start issue is the major problem that has ravaged the 3.0L Duramax. Sometimes, the dealership may have to attempt several possible causes before detecting the problem, meaning your truck may stay longer at the dealership. ... The Duramax LML got a few new emissions systems that the LMM didn't have, most ...Sep 12, 2014 · Pull each injector return line one at a time and crank. If there is more then just a small spit coming from an injector, its returning too much. Usually when an injector is bad it will be a steady stream of fuel coming from the top of the injector fuel return. Originally Posted by brokensmokin. If you’ve ever experienced the frustration of turning the key in your car’s ignition, only to have it crank without starting, you’re not alone. This issue, commonly referred to as ...

How are Chris I have a 2015 duramax 2500 with a 6.6 LML and it cranks but no start and it's showing no fuel pressure the - Answered by a verified GMC Mechanic ... 2011 lml duramax, crank no start. no codes. after cranking for a few seconds fuel rail pressure on the scanner shows 6,000-8,000 psi. ...The problem is no power to injectors (LB7 need 96DC volts). All circuits and harnesses are good. It was driving great, the customer drove home from work and would not start (it cranked great) the next morning. This all started mid Dec 2019. The ECM is commanding the FICM to supply the power to the injectors.

Loosen the bleed screw- [black screw next to the primer button] pump the primer until clear fuel comes out, tighten the screw- [careful, it is PLASTIC] pump the primer, crank for short 10 seconds, pump primer, crank 10 seconds. Some have a person pump while cranking. Pumping the primer will pull fuel even without a fliter or filter seal problem ...Going from the hot Florida climate to bitter cold in Ohio seemed to cause a fuel leak on our 2016 Chevrolet Duramax LML. Here we open it up and figure out wh...If the camshaft position sensor signal is interrupted while the engine is running the engine will operate normally. Circuit/System Verification. 1. Ignition ON. 2. Verify DTC P0641 is not set. ⇒ If the DTC is set. Refer to DTC P0641, P0651, P0697, P06A3, P06D2, or P06D6. ⇓ If the DTC is not set.The counter is managed by the ECU, if the problem would be a bad cam sensor or reluctor, the value would be wrong but would not reset. Frank@AutoPro. Category: Chevy. Satisfied Customers: 7,655. Experience: Expert. Verified. Frank@AutoPro and 87 other Chevy Specialists are ready to help you. Ask your own question now.2011 lml, no crank and no start. While driving the truck I hit a small pothole in the pavement and the engine died, would crank but no start. Disconnected the batteries for several minutes, then reconnected batteries but still no start. Had crank position sensor code, crank but no start. Replaced sensor and charged up the batteries.1. Start Relay Pin 86 -- Page B-6 (Should be +12 VDC) Post what voltage you have. If no +12 VDC there, check at UBEC Fuse # 13 ECM-BATT (2 Amp) for +12 VDC on both sides of Fuse. This Fuse Powers the Ignition Switch. Post what Voltage you find at this fuse. The Ignition Switch makes BCM_RC (HOT) +12 VDC which picks Relay RUN/CRANK by makingMA has the stuff to do it fairly cheap Merchant Automotive - Duramax Filter Head Rebuild Kit, 2001-2010 Duramax Doing this solved my problems the first time when I couldn't get it to prime. Also make sure you have a gas cap with a good seal :thumb My truck sat at a buddies house for a week because I couldn't get it to hold prime and start.2011 LML Won't Crank When cold. I have a deleted Chevrolet 2011 LML, with brand new batteries that behaves oddly when it's below 10 degrees Fahrenheit. It first happened a few weeks ago, before that I've had ZERO issues. Went outside to warm up the truck, and the glow plug light didn't illuminate when I turned the key on.

8350 posts · Joined 2010. #3 · Sep 26, 2014. First, verify that the filter is full of fuel before starting. Do not use ether! After that make sure the lift pump is pushing fuel to the filter head. If fuel is definitely going to the motor and it still wont start and stay running then you need to check rail pressure. Good scanners are not cheap.

19 posts · Joined 2009. #1 · Oct 28, 2014. OK I need a little help. I have an 08 I bought at an internet auction. Just got it to the shop and it has a no crank/ no start condition. I plugged in the scanner and it will not communicate with the truck. I have power and grounds at the dlc but no communication so no codes or data to give.

28. Nov 28, 2017. #12. r_olsen said: I just changed the fuel filter on my 2012 2500HD, after installing the filter I primed it and opened the bleeder screw and let the air out, repeated this until only fuel came out, let the truck idle for about 8 minutes to check for leaks, none so went for a test drive, but in drive the trunk has no power at ...687 posts · Joined 2016. #2 · Oct 5, 2018. After it has been run (warmed up), push the primer button until its firm, then see if it starts right up without excessive cranking. If it does start right up, its loosing prime. However, if it starts fine when cold, then prime would not be an issue. 2003 2500HD 6.6 duramax (LB7) all stock (no mods ...2015 Chevy Silverado 2500HD 6.6L Duramax 4X4 CC, LB, Tuned w/DSP5 switch, Studded, EGR & DEF Delete, FASS. (Daily Driver) 1982 Chevy K30 6.2L Detroit Crew Cab, Long Bed Dually 6" Lift (Under Construction) Planning for 6.5L or a 6.2L with Turbo.Jul 2, 2011 · nyterydr1500 Discussion starter. 30 posts · Joined 2009. #1 · Jul 2, 2011. went to grocery store and was inside for about 30 mins. came back out, started the truck like normal and it ran for about 30 sec. before dying. now it will crank but not start. fuel level is more than a 1/4 tank so that shouldn't be an issue. any suggestions or help ... first of all check for this wire rub and see how bad yours has worn through. its on the side that lays agains the ac compressor hard …LMM No Crank/No Start Again..... Thread starter KHHotshots; Start date Feb 5, 2016; Forums. Duramax 6.6 Technical. Duramax Hard Parts. LMM ... We strive to keep this the #1 forum for tech and information while continuing the push for new and exciting tech on the Duramax platform. From all out performance builds running 8 …12 posts · Joined 2019. #3 · Feb 5, 2020. For the no crank issue did you swap relays or check for voltage at pin #86. Check instrument cluster connector pins or it could be the inst. cluster (bad solder. connection). Could borrow another cluster and try it. 2004 Chev Silverado LT 2500hd 6.6 LLY.D. DuramaxNoKaOi Discussion starter. 392 posts · Joined 2008. #7 · Feb 10, 2014. Hey John, FYI I found out the injectors NEED minimum 1500 PSI of rail pressure to open, at least the LML with piezo injectors do, and I'd bet the older ones do too. I've got plenty of tips and suggestions for making it as easy as possible.Feb 5, 2016 · I got in, and tried to start it with the key. No Start, No Crank, Nothing but 1 click (Tracked down to relay). I have done the following trying to fix the problem. 1) Yes it is showing in Park, however I did try to start it in Neutral. 2) Security Light DOES GO OUT. 3) Changed Relays/Checked all Fuses. 11-16 LML Duramax Powertrain. Cranks, no Start. 440 Views 1 Reply 2 Participants Last post by forumoto , Nov 4, 2018. H. Hulky Discussion Starter · Oct 16, 2018. Add to quote; Share Only show this user. Hello all hope you guys can help me as well dont know where i should start from, anyway my company have a 2013 hd 3500 Duramax, 6.6 diesel ...2011 2500HD Silverado LTZ 6.6L Duramax LML No Mods. Save Share. Like. ... I've had 2 random long crank no start situations in 5 years after driving to the store like you did. Solved the first time giving it a couple of plunger pumps so that is what I did the 2nd time. No clue why it loses prime randomly like that and won't do it again for a ...

441 posts · Joined 2010. #14 · Nov 27, 2012. the wait to start light was not used on duramax engines. there is a light that looks like a curly line to represent a glow plug, but they do not have the wait to start like the old gm diesel engines did. the boss had the LB7, LLY, and LBZ engines and none of them had a wait to start light, just the ...I had to reprime after letting the truck sit for more than a couple of hours. Present: 2015 K2500HD LTZ Crew Cab Z-71. My Chevy Truck History: 2011 K2500HD LTZ Crew Cab LML. 2007 Classic K2500HD LT3 Crew Cab LBZ. 2006 K2500HD LT3 Extended Cab LBZ. 2003 K1500 LTZ X-Cab Z-71 5.3 Liter Gas. 1998 K1500 Silverado Z-71 5.7 Liter Gas.1. Jan 12, 2021. #1. 2016 LML will randomly lose almost all of the gauges, does not show what gear it is in and says service stabilitrak, service 4wd, service power steering, and service trailer system. Most of the time this condition lasts 30 seconds while driving, it will not shut off, but it does shift rough when it does it.2011 lml, no crank and no start. While driving the truck I hit a small pothole in the pavement and the engine died, would crank but no start. Disconnected the batteries for several minutes, then reconnected batteries but still no start. Had crank position sensor code, crank but no start. Replaced sensor and charged up the batteries.Instagram:https://instagram. just turkey 87thspectrum reference codesbike hero coolmath gamesarundel mills mall map maryland 1. Jan 12, 2021. #1. 2016 LML will randomly lose almost all of the gauges, does not show what gear it is in and says service stabilitrak, service 4wd, service power steering, and service trailer system. Most of the time this condition lasts 30 seconds while driving, it will not shut off, but it does shift rough when it does it.When you turn the key to start, you should get power on pin 86 on the starter relay. Are you? That should connect power from the battery to the 40 amp … mickey's farm qubocvs pharmacy hours west monroe la Hello everyone, I'm new to the discussion board. I have a 2012 Chevy duramax and I've been facing some issues with no crank, no start. The ecm was flashed, tunes were put back on the truck, I got it to fire up but as I'm driving down the road my gauges on the instrument panel all drop to zero, radio shuts off, ac controls shut off, service 4wd, service airbag, service tpms, anti theft ... routing number umpqua bank VEHICLE: 2003 GMC Crew Cab Dually 3500, 69k miles, color matched grill/door handles, all emblems removed, billet grill, 18% tinted windows, custom wheels (UGLY), Autometer gauges. PERFORMANCE PARTS: Idaho Rob tuned EFI, K+N Intake, Magnaflow 4" Exhaust w/ 5" tip, Edge chip removed (JUNK-blew out crank sensor twice), 15w-40 Amsoil Synthetic, New ...No Crank just one loud Click (LMM) I went to start my 2008 2500HD Duramax after it sat for 2 days coming down from a fairly tame drive down the mountain, all I got was a distinct "click". New batteries (under 1 month) each read 12.6V disconnected. I tried shorting the starter solenoid with a screwdriver, just made a few sparks.